High-Precision Ceramic Smart Manufacturing Base

Our in-house 3-axis CNC tooling center completes 3D CAD design in 2-3 days, 1:1 master physical mockups in 5-6 days, and high-pressure porous resin production dies in 12-15 days. Fired golden samples are typically dispatched via air courier within 45 to 60 days of CAD approval (45 days for kitchen and bathroom sinks and 60 days for toilets). Tooling charges are quoted per project based on mold complexity and are 100% refundable once cumulative order volumes reach the agreed milestone.

Current products (based on a 1,000-unit order): toilets — 60 days; kitchen and bathroom sinks — 50 days. Our strategic factory location is only 120 km from Tianjin Xingang Port, so container drayage to vessel cut-off takes just 2 hours, eliminating inland rail delays.

New OEM product development is quoted end to end from design approval: 45 days for kitchen and bathroom sinks and 60 days for toilets to a fired first sample, and 90 days for kitchen and bathroom sinks and 120 days for toilets to a finished 1,000-piece order.

Our annual production capacity is approximately 600,000 pieces across our tunnel and shuttle kilns.

Our Tangshan facility operates under ISO 9001 quality management. cUPC, CE, UKCA and WaterMark are listed for the relevant product lines and destination markets, with certificate file numbers available on request. Because a listing is issued per model, the scope is confirmed against the exact models on your order rather than assumed from the range.

Quality is built into the process and verified on 100% of production. Our automated lines cover precision batching with porous resin dies, high-pressure casting (HPC), robotic 6-axis cleanroom spray glazing, and firing in a 96-meter computerized tunnel kiln at 1200–1280°C. Every single unit then passes a strict 4-stage quality control pipeline: (1) raw mineral purity and slip rheology laboratory testing; (2) post-firing 100% optical inspection under 1,000-Lux lighting; (3) 100% hydrostatic, dual-flush and zero-leak testing; and (4) static weight load and extreme thermal shock destructive testing. In addition, our on-campus metrology and materials testing lab operates 4 standardized engineering test benches and rigs — including a 400 kg hydraulic static load press, a cyclic boiling water thermal shock tank, and a vacuum desiccator water absorption rig — tested in accordance with North American (ASME/cUPC), European (EN), and Australian (WaterMark) criteria.

For vitreous china toilets and basins, firing at 1200°C–1280°C brings the water absorption rate below 0.2%. Precise temperature control across the different zones of the tunnel kiln is our core manufacturing expertise.

Standard glaze is applied at 0.6mm – 1.0mm thickness. Optional upgrades are also available — you may choose one of three: premium self-cleaning glaze, antibacterial glaze, or nano-glaze.

It is a per-model value, and part of the answer is that 'thickness' means two different things on a sink. The rim that sits over the worktop is one measurement; the cast body wall is another, and the wall is thicker. On our inset CD series, for example, the rim is 0.71 in (18 mm ± 3 mm) and the body wall on the CD-86 is 1.26 in (32 mm ± 3 mm) — both published on the model pages. Toilet bodies typically run 10–12 mm. Read the figure for the model you are ordering off its own drawing, because that is the number the tool was cut to.

We offer a 10-year warranty on the ceramic body and a 1-year warranty on flushing mechanisms and accessories.

In the rare event of a defect, we provide 1:1 replacement or credit for the next order after verifying the issue with photos or videos.

Yes, every unit ships with its installation kit. For toilets: a soft-close seat, the flush mechanism and its fittings, floor fixing screws with decorative covers, a wax ring for a leak-proof seal, and an instruction manual. For kitchen sinks: a basket strainer and a bottom grid as standard, with a roll-up drying rack on the workstation models whose integrated ledge carries it.

HPC stands for High-Pressure Casting: the slip is injected into a reusable microporous mould under pressure, and the water is forced out through the pores so the ceramic particles compact against the mould wall. Our casting lines are developed and maintained in-house. What matters to a buyer is the outcome rather than the mechanism — a consistent wall section across a large body, which is something you verify with a wall-thickness report on fired pieces rather than take on trust.

Our factory is located in Tangshan, Hebei Province, China, a world-renowned ceramic production hub. We have a large showroom on site, and we also offer virtual tours via video call.

We use 5-layer corrugated or double-wall export cartons built to export-standard protection, with custom branding available. We offer flexible packaging solutions and fully support the standards adopted by our customers, ensuring safe transit and brand consistency.

Yes, we can provide plastic-free or reduced-plastic packaging options upon request.

Yes, we work with several reliable freight forwarders and can offer FOB, CIF, or DDP terms depending on your location.

Taitao was established in 2016, building on decades of local ceramic manufacturing expertise in Tangshan.

Use the enquiry form on this page, or the email and WhatsApp links in the page footer, and the export team will come back within one business day. Model or drawing, quantity, finish, target market and destination port are enough to start.

Yes, absolutely! Unlike single-category factories, TAITAO manufactures all three product families on one campus. We routinely consolidate fine fireclay sinks, thin-edge basins, and siphon toilets into single full container load (FCL) shipments, allowing importers and regional distributors to optimize inventory turnover without excess warehousing overhead.

We warmly welcome and facilitate third-party QA audits. Our facility features a dedicated 1,000-Lux inspection bay, granite calibration tables, MaP flush rigs, and hydraulic test benches specifically set aside for client inspection engineers. We also provide comprehensive in-house 100% inspection photo/video records before container sealing.

Our standard payment terms are a 30% T/T deposit in advance, with the remaining 70% balance paid prior to shipment.